Build your first computer

Ground yourself by touching an unpainted metal object. I will discuss the necessary steps. Attach the data cables to the drives. In this case, plug them into pins 1 and 4.

Some boards require particular sequences of memory installation, usually depending on the memory capacity, type, etc.

It is also polarity sensitive. Connect the PC speaker if equipped. If you installed a video card, remove it, to unlock the tab type just carefully bend the tab away from the card till the locking tab clears, eject the other type like you would with ram.

The SATA port is notched, so the cable can only fit in one way. All modern systems make use of the zero-insertion force ZIF socket.

Some motherboards have a power button on the board that can be pushed to accomplish this. Sit it on top of the standoffs you just installed so that each standoff lines up with a screwhole on the motherboard.

It is an easy step, but do it with Build your first computer. Push it into place, then spread the two arms out and position the screws into place over the four mounting screws you installed earlier.

Video Card Installation You must have a video card installed or operable onboard video in order to complete this tutorial so that you can see the output from your new PC once you turn it on. Screw them into the holes in the case or mounting plate that line up with holes on the motherboard.

Connecting the Motherboard Now it is time to begin connecting your newly installed motherboard to the various wires of your case as well as its power source. These are attached by metal, so they take some cutting, prying and twisting to break them free.

Most electrically sensitive hardware comes in a static bag which is designed to protect the electronics from static electricity shock. If it powers up, observe the system closely.

The front then pulls off. A screw extractor can help you grab those screws and get them out without messing with the hardware. If it does, it is connected properly to the motherboard.

Likewise, if the case you are using has been used before, it may have a power supply already installed. If your PC is not internet connected, you can activate it via telephone. Others need to be screwed in.

Building Your First PC?

Open up your motherboard manual to the diagram page that shows a layout of the motherboard. Check to be sure that the back of the motherboard is not touching any part of the case or mounting plate.

Some cases use a removable drive rack to hold the hard drive. If you get it backwards, the light may either never come on later or will stay on all the time when the PC is running. Keep in mind that if you miss the stated sequence to enter the CMOS setup before the boot sequence moves on, there is nothing wrong with just hitting the reset button and rebooting until you do catch what it is.

Once the unit is in place, check the back of the case and make sure the holes on the rear of the PSU line up with the screw holes on the case. Remove any protective cover from the bottom of the heatsink and verify there is heatsink compound on the part of the heatsink that will contact the top of the CPU.What to do if your new rig won’t boot; Building a computer used to be a complicated process, where careful selection of delicate parts was a necessity.

When that collection of components finally booted for the first time, it was a triumphant experience.

Knowing how to. How to install a power supply in your computer. How to install an Intel or AMD CPU in your PC. How to install new memory in your PC. How to replace your PC’s motherboard. How to install a graphics card. How to install a hard drive in your PC. The ultimate guide to proper PC cable management—you want your PC looking nice and pretty, after all.

Building Your First PC? Computer Builds FAQs: I often get questions such as: – Who are you to tell me which parts to choose?

How to Build Your Own PC

– Can you suggest me a step by step guide to build a computer? How to Build Your Own Computer 2. Is this your first build? Building a computer from scratch gives you the perfect machine for your needs, but it can be Read more Read Being more of a software gal than a hardware geek myself, I was the only Lifehacker editor who had never built a PC from scratch.

Building Your PC Once you have all the parts in hand, it’s time to get to building. Usually the first thing I do is test the system outside of the case to make sure all the parts are working together. For our first lesson in building your own PC, we start with a little computer hardware basics.

Lesson 2: Choose and Buy Your Parts. In this lesson, we'll show you how to .

Download
Build your first computer
Rated 4/5 based on 37 review